Search results

  1. O

    Voltage drop

    No under drive pullies, I have a tune but still drops. Can the fake voltage Gage when stopped and AC, lights on I am down by 12 sometimes 10. Everything dims. I will try idle speed today. If alternator going is there a recommended replacement with clutch pulley? Thanks. Sorry for delay been...
  2. O

    Voltage drop

    The voltage drop is getting annoying, especially with lights, wipers etc. What's best way to go? Under drives or I've seen a couple higher output alternators. Any suggestions? Thanks guys. Sent from my ADR6300 using Tapatalk 2
  3. O

    Brake Fluid

    I just went through a hectic bleed job when replacing tce lines. What I found useful and successful was bleeding in sequence. Right rear, left rear, front right, front left. I know some have had no issues but when I hit issues I did it this way and found a lot of air our of right rear. I also...
  4. O

    Power adjusting pedals

    Okay, awesome. Do they need a group buy? Has the company you're working with giving you a time frame? Thanks again Sent from my ADR6300 using Tapatalk 2
  5. O

    Power adjusting pedals

    Hey guys, I started noticing that my pedals only move a short distance. I remeber reading that a gear goes bad, has anyone made a fix for this issue or any dyi repair guide? Thanks in advance. Sent from my ADR6300 using Tapatalk 2
  6. O

    COP's.

    Yes I do, and tried following the link but it wont pick.up the sct, tried trouble shooting but no luck. Was wondering if it is because it was locked!? Would love to do it tho! Tired of this issue. If you have any knowledge besides the thread on here it would be a huge help. Thanks. Sent...
  7. O

    COP's.

    Just hitting the wall with all the issues on my miss/hesitation. So just getting some thorough research in before I get the plugs. If there is a better product I am willing to try. Sent from my ADR6300 using Tapatalk 2
  8. O

    COP's.

    Saw this product from a few other forums, was wondering what the thoughts were on them or other coils out there outside motorcraft for the mm. http://www.weaponxperformance.com/weaponx/catalogv137/level-1-street-coil-kit-ford-modular-v8-4v-p-282.html Sent from my ADR6300 using Tapatalk 2
  9. O

    SCT LiveLink - How to Log & Analyze Your Vehicle's Data

    Why will my x3 not even connect? Trying everything with cords and no luck. Tried to contact act but that was a loss. Does it news to be unlocked? Sent from my ADR6300 using Tapatalk 2
  10. O

    Good old brake pedal mush

    No kidding. And very worth the end result. Now just need to figure out the dumb AC and miss in motor. Sent from my ADR6300 using Tapatalk 2
  11. O

    Good old brake pedal mush

    Think it stayed in MC, but system got trashed and soft pedal for a while. After several bleeds, including one with car running I finally got it right on. Pedal and stopping is awesome. Finally feels like it should have. Thanks for all the help guys! And thanks to kns brakes and tce for the...
  12. O

    Good old brake pedal mush

    If air got into MC, how do I go about getting it out? That's the only thing I can think of without replacing booster or MC. So if someone can lend me a hand on that process before I have to spend more money and redo again. Sent from my ADR6300 using Tapatalk 2
  13. O

    Good old brake pedal mush

    Was reading on the crownvic site a bit about air getting into the MC and having to activate the ABS, is this the same issue on the mm? Is there a way to test the booster and the MC to determine the method of fixing if this next brake bleeding doesn't work? Sent from my ADR6300 using Tapatalk 2
  14. O

    Good old brake pedal mush

    No fluids leaking anywhere at MC or lines. Pedal gets rock hard while bleeding, but with car running goes to floor. Attempting another bleed. What piston could have a bad seal? In the MC or a caliper? Sent from my ADR6300 using Tapatalk 2
  15. O

    Good old brake pedal mush

    Bad MC seal? Something I can replace, or just a whole new MC and booster? Sent from my ADR6300 using Tapatalk 2
  16. O

    Good old brake pedal mush

    Just set up the tce brake lines and kns centric premium with hawks, and still a mush pedal. Going to try and bleed once more, although with gravity fill and bleeding I never had a stiffer pedal. just horrible on the road. If bleeding doesn't help is there any upgrades with a brake booster or...
  17. O

    F.Y.I. A/C inop

    How can I test them or replace them? There happen to be any write ups on this? Thanks. Sent from my ADR6300 using Tapatalk 2
  18. O

    F.Y.I. A/C inop

    Vacuum motors? Great. Probably what is just out of reach. How can I check those for function? I have suction from black hose in back of eatc unit. Any write ups on that procedure if I need to replace? The o rings are good, eatc redone by case and double checked here, blend door replaced. So I...
  19. O

    F.Y.I. A/C inop

    Would the compressor have anything to do with how the air blows through the vents? Been wondering if it has been going out for a while now. And I have been wondering if it has been locking up lately. Thanks in advance Sent from my ADR6300 using Tapatalk 2
  20. O

    Air ride leak

    Slow leak overnight, been thru two sets ofbags and solenoids. Replaced o rings on both sets. Complete deflation over night or at work. So soapy water doesn't show leak. Its so slow. But did try. Thinking about a different company. Sent from my ADR6300 using Tapatalk 2
Back
Top