fastblackmerc
Everything Marauder, LEDs & HI
Looking for an FPDM.
Wanted To Buy FPDM needed
- Thread starter fastblackmerc
- Start date
fastblackmerc
Everything Marauder, LEDs & HI
Bump.... Bump.....
fastblackmerc
Everything Marauder, LEDs & HI
Tried sending PM... got this message:
03Merc has exceeded their stored private messages quota and cannot accept further messages until they clear some space.
fastblackmerc
Everything Marauder, LEDs & HI
Trying to work a deal with 03merc. Will let you know.
Trying to work a deal with 03merc. Will let you know.
03Merc
Active member
fastblackmerc
Everything Marauder, LEDs & HI
Replied to your PM.
fastblackmerc
Everything Marauder, LEDs & HI
I had RacerX upgrade mine also and that is the problem, not with the upgraded FPDM but every time I start mine I get a CEL that throws a code related to the fuel pressure. I can't get my car through state inspection because of the CEL eventhough it's not emission related. MartyO sent me a new tune with a table or tables adjusted for a GT40 FPDM, but I can't get my PC(s) to recognize the SCT Xcalibrator2, so I can't upload a new tune.
cer0413
CRauder
Do you have windows 10?
fastblackmerc
Everything Marauder, LEDs & HI
No, Windows 7 64-bit.
I think the problems is the SCT Excalibrator 2 isn't supported. I see it in device manager and it's "working OK" but Liveload doesn't see. it.
RacerX
New England Marauder Member
How long did you run the car for with it like that? The tune Marty is trying to get you to load with the GT40 FP table has a good starting point so that it isn't too far out of range, but, over time it does learn and rewrite the table for more accurate values. Can you try driving it around more to rewrite the table?
Btw, I do have a dozen un modified FPDMs at any given time.
Btw, I do have a dozen un modified FPDMs at any given time.
Last edited:
cer0413
CRauder
Oh okay because I had 7 but it updated to 10. I had the same issue but SCT sorted it out remotely.
I have an SCT II and it works fine on Vista on my PC and Windows 8 on my laptop. Windows 7 should work too.
fastblackmerc
Everything Marauder, LEDs & HI
Windows device manager sees the tuner. The SCT software doesn't see it, keeps asking me to connect the tuner.
Device Manger says "Jungo - SCT Driver V10.11"
Last edited:
I don't know the answer.....
I do know that I had 2 fuel delivery hiccups on the way home from the dentist today. I'm thinking of changing my fuel pump from the Aeromotive 340 back to the Walbro GT40 pump that I saved after the swap. Then I will turn back on my Boost-a-Pump that I left installed, but turned off. Not sure if that is the answer or not. Other than that the the car runs flawlessly. The Musclemerc fuel filter is fresh. The RacerX modded FPDM should be ok. Water in gas? Who knows.
I do know that I had 2 fuel delivery hiccups on the way home from the dentist today. I'm thinking of changing my fuel pump from the Aeromotive 340 back to the Walbro GT40 pump that I saved after the swap. Then I will turn back on my Boost-a-Pump that I left installed, but turned off. Not sure if that is the answer or not. Other than that the the car runs flawlessly. The Musclemerc fuel filter is fresh. The RacerX modded FPDM should be ok. Water in gas? Who knows.
RacerX
New England Marauder Member
Which LiveLink do you have installed? After 4, I believe the USB driver was built into Livelink. With the SCT unplugged, open up Device Mangler in Windows, plug the SCT tuner in and let me know what pops up if anything and if there's an exclamation mark next to it.